Skip to content
Bayshore Estates Lock ServicesRequest a visit
Open 24/7(249) 800-5180Call now
Technician using a screwdriver on the deadbolt of an open blue-gray front door, with a tool bag and screw tray nearby. — Deadbolt Installation, Tollendal

Change or rekey · Tollendal

Deadbolt Installation in Tollendal

The old deadbolt has grown lazy. You turn the thumb-turn and the bolt creeps out halfway, then needs a second push with the door pulled tight.

Call now · open 24/7(249) 800-5180

Request a visit

In plain words

Most of the value in a deadbolt is on the frame side, which is why a good installation spends as much time on the jamb as on the door. The bolt is only as strong as the pocket it throws into and the screws that hold the strike. Short screws in a standard strike bite only into the thin jamb board; a reinforced strike fastened with 75 mm screws passes through that board into the stud behind, so a blow against the door meets the house rather than a strip of pine. The pocket is cut deep enough for a full throw and aligned so the bolt slides home freely.

Sound familiar?

The front door has a handsome lever and a keyed knob, and that is all. Nothing above it. When the door is shut, the only thing keeping it closed is a spring latch the width of a thumbnail, and you have started to notice.

How the visit goes

Deadbolt Installation · Tollendal

How the visit goes

Disassembled brass and steel lock cylinder parts laid on a gray metal surface with small brass pins, springs and tweezers. — Tollendal
  1. 1

    The frame behind the strike

    A bolt is only as good as what it throws into, so the jamb gets a hard look before anything is ordered. The locksmith checks whether the jamb is wood or steel, whether it is backed by solid framing at lock height or by a gap of shims and air, and whether earlier screws have torn out or been stripped. A jamb that flexes under a palm tells its own story. Where a strike has been fitted before, the old pocket is examined for depth and position, since a shallow or offset pocket is the usual reason an existing deadbolt feels stiff. This check decides between a plain strike, a reinforced strike with long screws, or a full-length jamb reinforcer.

  2. 2

    Fitting the bolt and setting the backset

    The bolt assembly slides into the edge bore with the faceplate set the way its maker marks, commonly the word "top" facing up. Most residential bolts adjust between 60 mm and 70 mm by twisting or sliding the faceplate, and the locksmith sets it to the backset measured earlier so the tailpiece from the cylinder lands in the centre of the bolt's cam. The bolt is secured with its two short screws, and the locksmith works it in and out by hand to feel that it runs freely through the door without rubbing on the bore. On an insulated door a round drive-in collar may replace the flat plate where the edge is too thin to mortise.

  3. 3

    A frame that now holds the bolt

    Behind the new strike plate is the part of the job you cannot see and will never need to think about. The pocket has been bored deep enough for the bolt to seat fully, the plate has been let into the jamb so it sits flush, and the long screws reach through the jamb into the framing behind it. On a door that had been forced or had stripped screw holes, a full-length reinforcer may sit under the strike. If you press the jamb with your palm now, it does not flex. That stiffness is what a bolt needs to do its work, and it is the reason the installation took as long on the frame as on the door.

In the van

  • Dry PTFE lubricant
  • Boring jig and 54 mm hole saw
  • Bolt faceplate or drive-in collar
  • Rekeying pins and key blanks
  • Jamb reinforcer

What affects the quote

  1. 1

    Mechanical, keypad or smart lock

    Electronic deadbolts carry a different hardware line and add setup time for codes, pairing to a phone and a walk-through, all of which appear as their own entries.

  2. 2

    Rental and building requirements

    Matching a building's keyway, providing keys to a landlord or fitting a lock that a condominium corporation specifies can add hardware or bench work, each shown as its own item.

  3. 3

    Door and hinge corrections

    A sagging door, loose hinge screws or thick weatherstrip are put right before a bolt is fitted, and that adjustment is quoted as its own line rather than folded into the lock.

Same fees day, night or weekend.

Have it ready

Before you call · 0 / 3

(249) 800-5180

Deadbolt Installation: questions

Advice · (249) 800-5180

Can a deadbolt be added to a door that only has a knob?

Yes, on nearly any wood, steel-clad or fibreglass entry door. The locksmith marks a spot above the knob, clamps a jig to the door and bores a cross hole through the face and a smaller hole through the edge, then cuts a pocket and fits a strike on the frame. The main things checked first are the door's thickness, what is inside it at that height and whether glass sits close by.

How long should the bolt be?

The bolt should extend at least 25 mm into the frame, which is the standard throw for a dwelling's entrance doors and the length most residential deadbolts provide. Part of the bolt stays inside the door for support while the rest sits in the pocket. A hardened steel insert that spins under a saw blade is a common feature worth having on doors that face a street or laneway.

Can a keypad or smart deadbolt be fitted instead of a keyed one?

Yes, and the preparation is the same. Many electronic deadbolts use the standard 54 mm bore and the same edge bore, so a door cut for a mechanical bolt often accepts one, and a keyed bolt fitted today can usually be swapped for a keypad later, subject to that model's own bore, backset and thickness needs. The locksmith checks door thickness against the model, fits a reinforced strike as usual, sets up codes with you and shows where the backup cylinder or battery terminals are.

Deadbolt Installation near you

Simcoe, Ontario

Tollendal information

Town
Tollendal, Simcoe, Ontario
In business
18 years
Hours
Open 24/7 · nights, weekends and holidays, same fees
Visits
On-site assessment preferred. Request a visit or call.

What the census means at the door

29%

Newer homes. About 29% of homes in Barrie were built in 1980 or earlier, according to the 2021 Census.

Builder-grade cylinders in newer homes are usually simple to pick and bump. Households who want their door to resist more than a casual try can move to a high-security cylinder that drops into the same hardware they already own.

58%

A mix of homes. Single-detached houses make up about 58% of homes in Barrie (2021 Census).

A mix of detached and attached housing means a mix of key habits: spare keys under pots at houses, fob-and-key combinations in buildings. A locksmith can improve both, with a proper key safe or keypad here and a tidy suite cylinder there.

Source: Statistics Canada, 2021 Census of Population

Open Tollendal in Google Maps

Open 24/7

Request a visit

The old deadbolt has grown lazy.

Call now · open 24/7(249) 800-5180
  • On-site assessment preferred
  • Same fees day, night or weekend
  • 18 years in business